At present, the installation structure of the purification workshop is made of purification board as wall panel and roof.
现在净化车间安装结构都是采用净化板做墙板及顶板。
Hebei Yibingda clean board manufacturer professional purification board production and sales,
河北意兵达洁净板厂家专业净化板生产销售，
1, for the purification workshop of the wall purification board, according to the layout of the wall panel and the installation order of batch stacking, to avoid secondary handling and rummaging, so as not to cause coating scratches, surface pollution, etc., Hebei purification board sales manufacturers to find the clean board.
1、对净化车间的墙面净化板，按墙面板排版图及安装顺序分批堆放，避免二次搬运及翻找，以免造成涂层划伤、表面污染等，河北净化板销售厂家找意兵达洁净板。
2, the installation of the wall panel in the purification workshop needs to ensure the perpendicularity to form a vertical plane, and the flatness is controlled by the perpendicularity.
2、在净化车间中墙面板的安装需保证垂直度，以形成垂直平面，通过垂直度控制平整度。
The installation starts from one end of the wall, and it is installed, adjusted and fixed.
安装时从墙面一端开始，边安装、边调整、边固定。
Installation tolerances must be measured and adjusted for every 5 wall panels installed.
每安装5排外墙板，必须测量一次安装公差，并进行调整。
Hebei purification board sales manufacturers looking for Italy bing da clean board
河北净化板销售厂家找意兵达洁净板
3, all self-tapping nails should be perpendicular to the wall panel, not inclined.
3、所有自攻钉都应垂直于墙板，不得倾斜。
Waterproof sealing materials must be provided in accordance with the requirements for the overlapping parts between the flooding plates, the Angle cladding plates, and the flooding plates, the Angle cladding plates and the molded steel plates.
泛水板之间、包角板之间以及泛水板、包角板与压型钢板之间的搭接部位，必须按照要求设置防水密封材料。
When using sealant materials, the width of sealant extrusion should be controlled at about 6mm, about 6m per tube of sealant, and the center line of sealant is 5 ~ 10mm from the edge of the plate.
使用密封胶材料时，密封胶挤出宽度应控制在6mm左右，每管密封胶约打6m，密封胶中心线距板边缘5～10mm。
The surface of the plate must be wiped clean before gluing, otherwise the sealing effect of the glue will be affected.
打胶前必须将板表面擦拭干净，否则将影响胶的密封作用。
Hebei purification board sales manufacturers looking for clean board
河北净化板销售厂家找洁净板
4. When laying the wall panel of the door and window opening, the size and position of the door and window opening should meet the design requirements, and the accurate position of the door and window opening must be ensured. The actual amount should be measured before cutting, and then the marking should be cut.
4、铺设门窗洞口墙面板时，门窗洞口尺寸、位置应符合设计要求，必须保证门窗洞口的准确位置，切割前要实测实量，然后划线再切割。
Hebei purification board sales manufacturers.
河北净化板销售厂家。
5. Structural reinforcement should be carried out on both sides of the hole (if there is no wall purlin on the hole, it should also be reinforced), and the reinforcement material is the same material as the wall purlin, according to the design drawing.
5、洞口两侧应进行结构加固（洞口上无墙檩时也应加固），加固材料与墙檩同材质，按设计图纸执行。
